Translate a message, then hear its rhythm
A Morse code translator converts written characters into sequences of short and long signals. On this page, type an English message and the dots and dashes appear as you write. Switch to Morse → Text to read a sequence you already have. Both directions use the same character table, so you can check a message without moving between different tools. The small character tiles beneath the controls show exactly how each letter contributes to the result.
Start with a short phrase such as HELLO WORLD. Listen once while watching the tiles, then listen again without looking. You can adjust the speed and tone before replaying. If you only need to check one symbol, the Morse code alphabet provides a larger reference sheet with a separate listening button for every supported character.
How to convert text to Morse code
- Select Text → Morse and enter your message in the left box, or the upper box on a phone.
- Read the live result. A single space separates encoded characters, while a slash separates words.
- Set the speed and tone, then select Play signal. Use Stop whenever you want to end playback.
- Choose Copy to copy the result, or Download WAV to save the generated sound.
Lowercase letters are converted to uppercase. Repeated spaces and line breaks in ordinary text become word separators. Numbers and supported punctuation are encoded alongside letters. An unsupported character produces a visible replacement and an explanation; playback and download stay unavailable until you correct it. This avoids quietly turning an incomplete conversion into an apparently finished recording.
Your input can contain up to 1,000 characters. Playback and WAV export are limited to three minutes per message, so very long text may need a higher WPM setting or several shorter excerpts. The result itself remains available to inspect and copy. Short passages are also easier to check by ear.
How to convert Morse code to text
Select Morse → Text, then paste your dots and dashes. Keep every character's signals together: A is .-, not . -. Separate characters with one or two spaces. Use a slash, a line break, or three or more spaces to mark a word boundary. When copying from a formatted document, check whether its spacing still describes the message you intended.
| Input in Morse mode | Decoded result | What to notice |
|---|---|---|
... --- ... |
SOS | Three separately written letters |
.... .. / - .... . .-. . |
HI THERE | A slash marks a new word |
.- -... |
AB | Each group is one character |
. - |
ET | An extra space changes the meaning |
This Morse code decoder accepts common dot and dash shapes, including a middle dot and a long dash. An underscore also acts as a dash in Morse mode. Mixed input is handled explicitly: recognized Morse groups are decoded and ordinary supported text is retained, with a notice that the input was mixed. For example, ... --- ... / HELP becomes SOS HELP.
In text mode, an isolated group containing two or more dots and dashes is treated as existing Morse when it has a known character match. A single period or hyphen remains punctuation. This practical rule is helpful for pasted notes, but it is inherently ambiguous. For literal strings made only of punctuation, check the character tiles before using the result. A slash in text mode is encoded as punctuation; in Morse mode it separates words.
Understand speed, pitch, and spacing
The WPM control changes how quickly the whole signal is sent. The default is 12 words per minute, and the available range is 5–40 WPM. WPM uses the conventional PARIS reference word rather than counting whatever words happen to be in your message. A sentence with many long characters therefore takes longer than a sentence with many short ones, even when their word counts match.
The tone control changes pitch between 300 and 1,000 Hz, with 600 Hz selected initially. Changing pitch does not change a letter's meaning. Choose a comfortable volume on your device before listening, and change the pitch if one frequency is easier for you to hear.
For playback, a dash lasts three dot units. The gaps within a character, between characters, and between words last one, three, and seven units respectively. You can hear why spacing matters by comparing the letter A with the two letters E T. The Morse alphabet with playable letters is a useful place to compare those rhythms one at a time.
Save a useful audio example
Download WAV creates a mono, 16-bit PCM sound file at a 22,050 Hz sample rate using your current speed and tone. The browser generates the tones directly; there is no prerecorded voice or audio track. Very short fades at the edges of each tone reduce abrupt clicks without changing the planned signal durations.
Use the download for a classroom example, a listening exercise, or a puzzle soundtrack. First copy the written result into your notes so you have an answer key. Play the saved file once before sharing it, especially if another application will edit or compress it. Changing the gaps during editing can change how a listener interprets the message.
Common mistakes worth checking
- Missing letter boundaries: an unbroken string of dots and dashes does not always have one unambiguous reading. Add spaces where the characters belong.
- Confusing zero and O: zero is five dashes; the letter O is three. The font and character tiles help you inspect the difference.
- Treating Morse as encryption: anyone with the alphabet can decode it. It is useful for puzzles and signals, but it does not provide confidentiality.
- Assuming every symbol is standard: this tool includes common punctuation extensions as well as the core letter and number set. Check the recipient's conventions when exchanging technical messages.
The Morse code encoder and decoder on this page operate locally in your browser. They do not send your message to a translation API, and you do not need an account. This page handles written text and written Morse; it does not listen to an audio recording. For a printable overview of the supported symbols, open the complete Morse code letters and numbers table.